Eagle’s Rest – Jackson Hole, WY

This quad was built along the lift line of a previous Murray-Latta double with a three year gap between the two.
This is the first Skytrac lift in the state of Wyoming.
Monarch drive-tension terminal.
View up from the base terminal.
The lift is sandwich between the Bridger and Sweetwater gondola alignments.
The first few towers.
Upper part of the lift line.
The top terminal labelled as tower 8.
View down the line.
Peak return terminal.
Skytrac tower head with Leitner-Poma sheaves.
View down from the summit.
The top terminal and tower 7.
Unloading area and operator house.
Tower 6.
Middle part of the line.
Skytrac chair with Kidstop from Leitner-Poma.
The top of tower 5.
View up at tower 4.
Uphill end of the bottom terminal.
Lift overview.
Note the bottom shack is on the light side due to space constraints.

13 thoughts on “Eagle’s Rest – Jackson Hole, WY

  1. Collin Parsons October 12, 2019 / 1:47 pm

    This lift has the same ending location as the old one, but does not start in the same place. The old lift started right next to Teewinot. This lift follows a route closer to and parallel to the Bridger Gondola, and does not appear to start at the base. You’d have to ride Sweetwater to mid first and then ski down to this lift and lap it.


  2. New England Chairlifts & Skiing October 12, 2019 / 5:22 pm

    Honestly I really am not a fan of the Skytrac chair design at all. It just looks ugly. The bail/omega chairs look much better in my opinion.

    Liked by 1 person

    • Donald Reif October 12, 2019 / 6:42 pm

      Me neither. If this lift had Doppelmayr’s EJ chairs, it’d be a different story (since the Skytrac lifting frames are closer in resemblance to Doppelmayr’s design than Leitner-Poma’s).

      Liked by 1 person

    • Kaden K October 17, 2019 / 8:24 pm

      Really? I don’t think they look that bad.


    • Somebodyelse September 10, 2020 / 6:55 pm

      Skytrac’s double chairs are about the only one which look right.


  3. Max Hart October 18, 2019 / 8:33 am

    Note the L-P sheaves and assemblies.


    • bobby smith January 2, 2020 / 1:01 pm

      They are not L-P sheaves or assemblies. They are 100% Skytrac design.


      • themav January 2, 2020 / 8:29 pm

        Looks like LPOA sheaves in a Skytrac/CTEC style frame


        • vons3 February 15, 2020 / 8:16 pm

          You are correct LPOA sheaves mounted in Skytrac sheave beams, this was a popular combo of components offered in 2019, I think only Lookout Pass whent 100% skytrac.


  4. gavin November 12, 2019 / 5:09 pm

    Why doesn’t it start at the base? doesn’t that waste a ride on Sweetwater?


    • Somebody November 12, 2019 / 6:12 pm

      There’s no space down at the base.


  5. Sam November 12, 2019 / 5:44 pm

    how do you bump a skytrac chair?


    • Ryan Murphy November 12, 2019 / 7:33 pm

      The small handle on the outside is what I’ve seen lifties use, and it’s what I use when I self bump.


Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Google photo

You are commenting using your Google account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s