Copper Mountain, CO

Click on a lift’s name for pictures.  View in fullscreen↗

33 thoughts on “Copper Mountain, CO

  1. Carson February 4, 2018 / 1:17 pm

    Does anyone know what lift dumb and dumber was filmed on during when hairy got his tongue stuck on the chair?

    Like

  2. Michael February 4, 2018 / 3:36 pm

    E Lift. The Yan triple before Excellerator. The scene was actually filmed on the deck of Solitude Station on a chair that was a spare from under the summer deck.

    Liked by 1 person

  3. Carson February 4, 2018 / 7:25 pm

    Thanks! Did E lift sell?

    Like

  4. Matt February 4, 2018 / 7:33 pm

    From what I know the chairs were reused on S lift, before being replaced by CTEC chairs. The rest of the lift I believe was scrapped but I could be wrong.

    Like

    • John February 28, 2018 / 2:02 pm

      E’s carriers did go to S. The gearbox and drive bullwheel went to R, as did the tower assemblies and lifting gantries (R originally had none).

      Like

  5. John February 28, 2018 / 2:03 pm

    Peter- you show that C-lift was removed. It wasn’t, I still maintain it. Its other name is Gem.

    Like

  6. GreatEight January 14, 2019 / 2:47 pm

    Peter, are you heading to Colorado soon to take pictures of the new American Eagle and Flyer?

    Like

    • Peter Landsman January 14, 2019 / 2:50 pm

      I plan to get to Copper within the next month or so. I already got the rest of the new lifts in Colorado but the Flyer was not open yet at that time. I will get Taos as well when I go to Copper.

      Liked by 3 people

  7. bryansouth January 19, 2019 / 9:17 pm

    Rode the new chairs today. American Flyer is quite the thrill ride. Durring stops (which it does quite often) it rolls backwards quite a ways. In certain spots it also can drop and bounce probably 30 feet or so. It honestly felt very unsafe.

    Liked by 1 person

    • John March 6, 2019 / 9:49 am

      The lift does not roll back. What you’re experiencing is the line equalising itself. Consider how much weight is on the heavy side, and the associated momentum. When the lift stops the weight sags in between towers on the heavy side, then the light side becomes tight and wants to pull back. It always takes several back-and-forth cycles like this to come to rest after a stop. The lift is safe. The old one did this as well, but it wasn’t as noticeable with the lighter carriers.

      Liked by 1 person

  8. Kaden K March 5, 2019 / 10:52 pm

    The Old E chair at Copper had bubbles?

    Like

  9. Michael March 6, 2019 / 5:51 am

    No. The original F lift at Copper had bubbles.

    Like

  10. Maxwell September 13, 2019 / 4:45 pm

    Timberline express is 1100 not 1000

    Like

    • John September 14, 2019 / 9:42 am

      We’ve had eyes on that area for years- in fact, there was once a map with lifts 8,9, and 10 in that basin. I think we’re looking more at upgrading and refining what we already have though. Hard to say.

      Like

  11. Donald Reif October 31, 2019 / 6:39 pm

    Blackjack received a Skytrac return station in 2019 as the loading area had to be moved to accommodate the Three Bears lift.

    Like

    • skitheeast February 23, 2020 / 9:10 pm

      What is the point of replacing Super Bee, a detachable six-pack still young enough to keep going for a number of years, with another detachable six-pack? I agree East Village needs more out-of-base capacity, but this would not do anything. The Timberline replacement makes some sense, as it does get backed up sometimes, and the equipment is new enough/in good enough shape where it could be moved over to Lumberjack and upgrade that lift. I think the Lumberjack base would have to stay where it to please the homeowners in that area. I also like the idea of an infill lift, although I think that your location is not ideal. It cannot be an effective lapping lift, as everyone would be forced onto Coppertone, and it does not effectively move people around the mountain.

      Some other ideas worth considering: Alpine is old, long, and could very easily service the Far East Lot with a small bridge or tunnel spanning CO-91. Upgrading it to a detachable quad could allow them to charge for parking in Far East. Union Meadows is an underutilized part of the mountain due to it requiring a Timberline to Sierra link to lap. An expansion lift there could help spread skiers out. Speaking of Sierra, it could use a capacity upgrade as well, as it also can get decent lift lines primarily because it has such low capacity. Mountain Chief is really old and could go to a fixed-grip triple to match Three Bears.

      Liked by 1 person

      • Donald Reif February 25, 2020 / 11:01 am

        I think the Master Plan has Alpine being upgraded to a high speed quad and being extended a bit higher up to the top of Copperopolis.

        Like

  12. vons3 February 23, 2020 / 9:58 pm

    Honestly the infill lift would work better if it replaced Rendezvous lift ending in the same spot but starting around CB2 (snowmaking control building off of coppertone), that way the lift could receive traffic from both Flayer and Eagle and move it to copper bowl while providing some good blue green lap terrain. Doubt capacity changes to 6 or 4 as all the lifts in the bowl are all designed for 1200pph though blackjack(4) can be upgraded to a triple (maybe use L chairs when it is replaced to upgrade cap). Timberline should be upgraded as its’ a popular trail system, and the existing lift would be a good replacement for Lumberjack on its existing line.

    Like

  13. jcpierce05 February 23, 2020 / 10:20 pm

    New Super Bee Express: I agree with skitheeast. Whats the point of replacing a 6 chair with a 6 chair? I don’t think the lift has high hours on it. If your cold, well, skiing might just not be for you, or go to Center Village and catch the Flyer. The only thing I could see being possible for a future replacement of this lift is a gondola, but that’s a push.
    Idea: Replace Alpine with high speed quad.

    Care Free Express: This lift would be practically pointless. Center Village holds its capacity well. The longest I have ever had to stand in a line at the Flyer is 10 minutes. Eagle has been about 7.
    Idea: I like Vons3’s idea for a High Speed quad from where Liberty and Coppertone meet to the top of the R lift.

    Timberline Express: I think this should be the next lift on the chopping block. It’s a bottleneck on the mountain.

    Lumberjack Replacement: There is no point in replacing Lumberjack, and extending it uphill would be a pain in the a** for beginner skiers. The lift does not get lines. Yes, ride time is a bit long, but the only time I would see a replacement there is when they expand into Union Meadows. I would extend the lift uphill to service that terrain.

    Here’s some other thoughts:

    Timberline to a 6 chair and re-use Timberline to replace S lift- I am quite surprised that this did not happen before Tucker Mountain and they didn’t re-use S on Tucker.

    Storm King to a triple chair as its been getting pretty backed up. Maybe use the equipment to expand into Union meadows

    Other than that, Copper is in pretty good standing with their lifts.

    Like

    • Donald Reif February 23, 2020 / 10:51 pm

      Instead of the Care Free lift, I would upgrade Rendezvous to a high speed quad and extend it downhill to a point where it could be accessed from Solitude Station.

      Like

      • BarkeeStone February 24, 2020 / 9:13 am

        That could work. But wouldn’t it be likely relocated from it’s original spot and make the line down CopperTone and where it ends.

        I could do that.

        Like

    • skitheeast February 24, 2020 / 12:17 am

      It would be awesome if Storm King was converted to an actual chairlift instead of a t-bar. However, Copper insists the winds on the liftline would not permit a chairlift to run on many days. Personally, I think that is because it rides Hallelujah Ridge all the way up so it is super exposed, and perhaps a chairlift could work with a base at the intersection of Easy Road and Coppertone (allowing access from Solitude Station). This liftline would be shielded from most of the wind that goes over the ridgeline.

      Something else I have always wondered is why Sierra does not go the extra 100 feet to access Copper Bowl and unload next to Mountain Chief. If it is winds, then why does Mountain Chief unload where it does on the ridgeline?

      Like

      • Thomas Jett February 24, 2020 / 1:45 pm

        The Master Plan addresses your Sierra question and attributes the issue to wind. Copper views it like this: Sure, Mountain Chief is already on the ridge, but most people riding Sierra don’t want the backside; they want the face. Even if Union ended on the ridge, you’d still have to hike Copper Bowl. The Master plan leaves open the option that when Sierra gets replaced with a D4C, it gets realigned to end at the top of Union Peak.

        Liked by 1 person

        • vons3 February 24, 2020 / 7:09 pm

          Since the install of Celebrity Ridge platter it’s unlikely any new S lift would change from the current alignment.

          Like

      • pbropetech February 25, 2020 / 8:45 am

        Storm King has the most wind-related downtime of any of our lifts. Placing a realigned lift where you suggest won’t change that- if you look at that side of Copper Peak, you’ll notice that there’s no snow there because the same wind rips it off the face.

        Like

        • Michael February 25, 2020 / 11:12 am

          When Copper built the original Storm King, people would ask me why it was closed (5-10mph wind at the bottom). I would reply “Did you watch the news this morning when they said that the Jet Stream was dipping down into Colorado? The top terminal IS IN the Jet Stream!”

          Liked by 1 person

        • Joe Blake February 26, 2020 / 6:14 pm

          @Michael – since quibbling over minutiae seems de rigueur here, I will point out that the mid-latitude jet is generally above 350 hPA (25 grand-ish), usually over 200 knots windspeed. The winds that you and my oldest bro describe here are surface winds. Certainly not less snow-scrapy for the distinction, just different semantically.

          Like

        • Michael February 27, 2020 / 8:06 am

          @jJoe – Apparently the folks I was talking to did not have your expertise regarding the jet stream. They nodded their heads and smiled as if they understood the concept;-)

          Like

        • Joe Blake March 3, 2020 / 7:58 am

          @michael – Perfect. Follow up question: Where do you put the moguls at night and how do you get them back on some of the runs and not others?

          Like

Leave a Reply to Kaden K Cancel reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Google photo

You are commenting using your Google account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s